Defining Domes
Domes are surfaces that curve in two directions. The most common domes spring from a circular base and for that we call them "circular domes" at Geometrica, even if their cross-section is not circular. So the term "circular dome" differentiates domes on a circular base from Freedomes® that spring from bases of other shapes.

While their base is circular, these domes can still have quite a variety of shapes and structure. Three main geometric parameters that define a circular dome are meridian, pattern and layers.


Circular domes are surfaces of revolution. These surfaces are generated by rotating a meridian curve about a vertical axis. The meridian curve is then one half of the curve at a vertical section through the center of the dome.

Circular Dome Meridian

Meridian curves are similar to the cross-sectional curves of vaults - they may be optimized for certain loads, or shaped to "hug" any clearance line desired. For example, if there are large apex forces, an acute geometry provides a positive slope near the apex load to resist the load, or in storage applications with automated stacker-reclaimer equipment, the meridian may start nearly vertical, and then quickly turn into a more gentle slope as in this 133m sulfur storage dome.

Sulfur Storage Dome


Although square-grid and radial geometries (or combinations of these) are sometimes used in domes, the in-surface geometry of the dome should really be fully triangulated in order to develop the full benefits of shell-action.  A dome with square patterns on the surface will generally result in a more costly solution. R. Buckminster Fuller's "geodesic dome" may be the most famous way to subdivide a sphere into nearly-equal and nearly-equilateral triangles. Other in-surface geometries include Lamella, Kiewitt, Schwedler and Geometrica's own Lace™ geometry.

Circular Dome
Lace™: This geometry is generated from a uniform triangular grid trimmed to a dodecagon shape, then stretched to form a circle, and finally wrapped onto the surface of revolution. The resulting geometry is structurally efficient. It also maintains nearly-equilateral triangles and has a uniform base. Some of the largest domes in the world, such as the 133 m Ruwais dome in the UAE, the 142m San Cristobal dome in Bolivia, and the 122m JEA domes in Florida are built with the Lace geometry, or with a lamella-lace combination geometry.

​                                    ​​ 
Lace Grid Structure

 Lamella Domes
Lamella: Lamella domes are generated with concentric rings, where each subsequent ring is rotated by a half module. This reduces the length of the ring tubes as the geometry proceeds towards the apex. When the tubes of the rings become too small (usually half the length of the first), they "consolidate" to the next ring, joining the two divisions into one. The separation between rings in Lamella domes can be varied so they are equilateral triangles forming each ring. Because the tubes of each ring are equal, the manufacturing time is fast and assembly is easy. Lamella domes are beautiful and good for architectural applications. Ref: the Cancun Hyatt and the Mustafa Centre.

Lamella Dome StructureLamella Glass Cladding
Kiewitt Domes

Kiewitt: Kiewitt domes are also generated with concentric rings. Generation starts from the base with a specific number of divisions making the modules of a reasonable length. Then subsequent rings reduce the number of divisions by the number of segments in the dome. Generally the number of segments is set between 5 and 8. As with Lamella domes, the horizontal Kiewitt rings provide an easy check during construction, but the pattern results in many more different parts. Kiewitt domes include the 112m Marchwood dome in the UK.


 Geodesic Domes
Geodesic: A geodesic dome starts with a regular polyhedron (generally an icosahedron), and subdivides each triangular face to then project the new nodes onto the surface of the sphere. As in the Lace geometry, the geodesic geometry has nearly-equilateral triangles, but the base of the dome is generally not uniform unless the dome is a hemisphere. Also, the geodesic pattern is limited to spherical domes.


Geodesic Dome Designs

 Schwedler Domes
Schwedler: This geometry is generated by laying out principal members along meridians and rings, and then introducing diagonals to triangulate the rectangular modules. It is easy to generate, but not very efficient. Diagonal members are substantially longer than ring or meridian bars, and must therefore be more robust to resist buckling loads. It finds some application in glass-clad domes, as trapezoidal glazing is less expensive than triangular. For other uses this geometry will result in structures 20 to 30% heavier than the alternative geometries.
Depending on the number of layers of chord elements, domes may be single-layer, double-layer-vierendeel, double-layer-truss, or ribbed.
Single layer geometries are used for moderate spans and for architectural applications. 

Single Layer Geometric Pattern

Vierendeel geometries can be used for most circular domes and freedomes. These are double-layer frames with parallel nodes in each layer connected with post members perpendicular to the dome's surface. The second layer increases the bending strength and the buckling resistance without introducing unnecessary web elements.


Double Layer Geometric Pattern

Double layer truss geometries are used whenever there are large or concentrated loads, column supports, or for extremely long spans.

Ribbed Geometric Pattern

Ribbed geometries are also used in domes. They are easy to install because most of the assembly work may be done on the ground and lifted into place.

Ribbed Geometric Design

Both the double layer truss and the ribbed geometries may benefit from increased chord density.
The Marchwood dome is an example of a dome where various geometries were combined. The ribbed and single-layer geometries are used in the bottom rings of the dome, when a double layer geometry was used in its main areas.


Marchwood Dome Design